Construction

Tap & Clearance Drill Sizes — Imperial

Inch tap drill chart for UNC, UNF and UNEF threads #0 to 3 in: makers' tap drills, % of thread, class 2B minor limits, forming-tap drills and clearance holes.

Drill a 1/4-20 UNC hole with a #7 drill (0.201 in, 5.1 mm) and a 1/4-28 UNF hole with a #3 drill (0.213 in). Other common sizes: #6-32 takes #36, #8-32 takes #29, #10-24 takes #25 or #26, #10-32 takes #21, 5/16-18 takes F, 3/8-16 takes 5/16 in and 1/2-13 takes 27/64 in (Greenfield 2024 catalogue, Regal). These drills cut roughly 70–80 % of full thread. ASME B1.1 class 2B nut threads allow about 83 % down to 53–66 %, depending on size (Emuge). To find a drill for any other size, use percent of thread = TPI × (major Ø − drill Ø) ÷ 0.01299, or for a given percentage, drill Ø = major Ø − 0.01299 × % ÷ TPI. The tables below show the makers' drills, the hole limits, the percentage each drill gives, drills for thread-forming taps, and close- and normal-fit clearance holes. To turn a decimal hole size into the nearest fractional drill, use the Decimal to Fraction Converter.

UNC and UNF tap drill chart (#0 to 3 in)

ThreadMajor Ø (in / mm)Minor Ø, class 2B min–max (in) (thread %)Tap drill, cutting tap (Greenfield)Thread % at that drill (calc.)Hole Ø, Emuge (in / mm)Drill for a forming tap (Greenfield)
#0-80 UNF0.0600 / 1.520.0465–0.0514 (83–53 %)3/64 in = 0.0469 in / 1.19 mm81 %0.0480 in / 1.22 mm#54 = 0.0550 in
#1-64 UNC0.0730 / 1.850.0561–0.0622 (83–53 %)#53 = 0.0595 in / 1.51 mm67 %0.0595 in / 1.51 mm#51 = 0.0670 in
#1-72 UNF0.0730 / 1.850.0580–0.0634 (83–53 %)#53 = 0.0595 in / 1.51 mm75 %0.0595 in / 1.51 mm#51 = 0.0670 in
#2-56 UNC0.0860 / 2.180.0667–0.0737 (83–53 %)#50 = 0.0700 in / 1.78 mm69 %0.0700 in / 1.78 mm5/64 in = 0.0781 in
#2-64 UNF0.0860 / 2.180.0691–0.0752 (83–53 %)#50 = 0.0700 in / 1.78 mm79 %0.0730 in / 1.85 mm#47 = 0.0785 in
#3-48 UNC0.0990 / 2.510.0764–0.0845 (84–54 %)#47 = 0.0785 in / 1.99 mm76 %0.0820 in / 2.08 mm#43 = 0.0890 in
#3-56 UNF0.0990 / 2.510.0797–0.0865 (83–54 %)#46 = 0.0810 in / 2.06 mm78 %0.0827 in / 2.10 mm2.3 mm = 0.0906 in
#4-40 UNC0.1120 / 2.840.0849–0.0939 (83–56 %)#43 = 0.0890 in / 2.26 mm71 %0.0890 in / 2.26 mm#38 = 0.1015 in
#4-48 UNF0.1120 / 2.840.0894–0.0968 (84–56 %)#42 = 0.0935 in / 2.37 mm68 %0.0945 in / 2.40 mm2.6 mm = 0.1024 in
#5-40 UNC0.1250 / 3.180.0979–0.1062 (83–58 %)#38 = 0.1015 in / 2.58 mm72 %0.1015 in / 2.58 mm#33 = 0.1130 in
#5-44 UNF0.1250 / 3.180.1004–0.1079 (83–58 %)#37 = 0.1040 in / 2.64 mm71 %0.1063 in / 2.70 mm2.9 mm = 0.1142 in
#6-32 UNC0.1380 / 3.510.1040–0.1140 (84–59 %)#36 = 0.1065 in / 2.71 mm78 %0.1110 in / 2.82 mm1/8 in = 0.1250 in
#6-40 UNF0.1380 / 3.510.1110–0.1190 (83–59 %)#33 = 0.1130 in / 2.87 mm77 %0.1181 in / 3.00 mm3.25 mm = 0.1280 in
#8-32 UNC0.1640 / 4.170.1300–0.1390 (84–62 %)#29 = 0.1360 in / 3.45 mm69 %0.1360 in / 3.45 mm#25 = 0.1495 in
#8-36 UNF0.1640 / 4.170.1340–0.1420 (83–61 %)#29 = 0.1360 in / 3.45 mm78 %0.1378 in / 3.50 mm#24 = 0.1520 in
#10-24 UNC0.1900 / 4.830.1450–0.1550 (83–65 %)#26 = 0.1470 in / 3.73 mm79 %0.1520 in / 3.86 mm11/64 in = 0.1719 in
#10-32 UNF0.1900 / 4.830.1560–0.1640 (84–64 %)#21 = 0.1590 in / 4.04 mm76 %0.1614 in / 4.10 mm#16 = 0.1770 in
#12-24 UNC0.2160 / 5.490.1710–0.1810 (83–65 %)#16 = 0.1770 in / 4.50 mm72 %0.1770 in / 4.50 mm#8 = 0.1990 in
#12-28 UNF0.2160 / 5.490.1770–0.1860 (84–65 %)#15 = 0.1800 in / 4.57 mm78 %0.1820 in / 4.62 mm#7 = 0.2010 in
1/4-20 UNC0.2500 / 6.350.1960–0.2070 (83–66 %)#7 = 0.2010 in / 5.11 mm75 %0.2040 in / 5.18 mm#1 = 0.2280 in
1/4-28 UNF0.2500 / 6.350.2110–0.2200 (84–65 %)#3 = 0.2130 in / 5.41 mm80 %0.2165 in / 5.50 mm15/64 in = 0.2340 in
5/16-18 UNC0.3125 / 7.940.2520–0.2650 (84–66 %)F = 0.2570 in / 6.53 mm77 %0.2610 in / 6.63 mmL = 0.2900 in
5/16-24 UNF0.3125 / 7.940.2670–0.2770 (84–66 %)I = 0.2720 in / 6.91 mm75 %0.2717 in / 6.90 mmM = 0.2950 in
3/8-16 UNC0.3750 / 9.530.3070–0.3210 (84–67 %)5/16 in = 0.3125 in / 7.94 mm77 %0.3160 in / 8.03 mmS = 0.3480 in
3/8-24 UNF0.3750 / 9.530.3300–0.3400 (83–65 %)Q = 0.3320 in / 8.43 mm79 %0.3346 in / 8.50 mmT = 0.3580 in
7/16-14 UNC0.4375 / 11.110.3600–0.3760 (84–66 %)U = 0.3680 in / 9.35 mm75 %0.3680 in / 9.35 mmY = 0.4040 in
7/16-20 UNF0.4375 / 11.110.3830–0.3950 (84–65 %)25/64 in = 0.3906 in / 9.92 mm72 %0.3898 in / 9.90 mmZ = 0.4130 in
1/2-13 UNC0.5000 / 12.700.4170–0.4340 (83–66 %)27/64 in = 0.4219 in / 10.72 mm78 %0.4219 in / 10.72 mm15/32 in = 0.4688 in
1/2-20 UNF0.5000 / 12.700.4460–0.4570 (83–66 %)29/64 in = 0.4531 in / 11.51 mm72 %0.4528 in / 11.50 mm12.25 mm = 0.4823 in
9/16-12 UNC0.5625 / 14.290.4720–0.4900 (84–67 %)31/64 in = 0.4844 in / 12.30 mm72 %0.4844 in / 12.30 mm17/32 in = 0.5312 in
9/16-18 UNF0.5625 / 14.290.5020–0.5150 (84–66 %)33/64 in = 0.5156 in / 13.10 mm65 %0.5118 in / 13.00 mm13.5 mm = 0.5315 in
5/8-11 UNC0.6250 / 15.880.5270–0.5460 (83–67 %)17/32 in = 0.5312 in / 13.49 mm79 %0.5313 in / 13.50 mm14.75 mm = 0.5807 in
5/8-18 UNF0.6250 / 15.880.5650–0.5780 (83–65 %)37/64 in = 0.5781 in / 14.68 mm65 %0.5709 in / 14.50 mm15.25 mm = 0.6004 in
3/4-10 UNC0.7500 / 19.050.6420–0.6630 (83–67 %)21/32 in = 0.6562 in / 16.67 mm72 %0.6563 in / 16.67 mm45/64 in = 0.7031 in
3/4-16 UNF0.7500 / 19.050.6820–0.6960 (84–67 %)11/16 in = 0.6875 in / 17.46 mm77 %0.6890 in / 17.50 mm23/32 in = 0.7188 in
7/8-9 UNC0.8750 / 22.230.7550–0.7780 (83–67 %)49/64 in = 0.7656 in / 19.45 mm76 %0.7656 in / 19.45 mmno form tap
7/8-14 UNF0.8750 / 22.230.7980–0.8130 (83–67 %)13/16 in = 0.8125 in / 20.64 mm67 %0.8071 in / 20.50 mmno form tap
1-8 UNC1.0000 / 25.400.8650–0.8900 (83–68 %)7/8 in = 0.8750 in / 22.23 mm77 %0.8750 in / 22.23 mmno form tap
1-12 UNF1.0000 / 25.400.9100–0.9280 (83–67 %)59/64 in = 0.9219 in / 23.42 mm72 %0.9219 in / 23.42 mmno form tap
1-1/8-7 UNC1.1250 / 28.580.9700–0.9980 (84–68 %)63/64 in = 0.9844 in / 25.00 mm76 %0.9843 in / 25.00 mmno form tap
1-1/8-12 UNF1.1250 / 28.581.0350–1.0530 (83–67 %)1-3/64 in = 1.0469 in / 26.59 mm72 %1.0433 in / 26.50 mmno form tap
1-1/4-7 UNC1.2500 / 31.751.0950–1.1230 (84–68 %)1-7/64 in = 1.1094 in / 28.18 mm76 %1.1094 in / 28.18 mmno form tap
1-1/4-12 UNF1.2500 / 31.751.1600–1.1780 (83–67 %)1-11/64 in = 1.1719 in / 29.77 mm72 %1.1719 in / 29.77 mmno form tap
1-3/8-6 UNC1.3750 / 34.931.1950–1.2250 (83–69 %)1-7/32 in = 1.2188 in / 30.96 mm72 %1.2205 in / 31.00 mmno form tap
1-3/8-12 UNF1.3750 / 34.931.2850–1.3030 (83–67 %)1-19/64 in = 1.2969 in / 32.94 mm72 %1.2992 in / 33.00 mmno form tap
1-1/2-6 UNC1.5000 / 38.101.3200–1.3500 (83–69 %)1-11/32 in = 1.3438 in / 34.13 mm72 %1.3386 in / 34.00 mmno form tap
1-1/2-12 UNF1.5000 / 38.101.4100–1.4280 (83–67 %)1-27/64 in = 1.4219 in / 36.12 mm72 %1.4173 in / 36.00 mmno form tap
1-3/4-5 UNC1.7500 / 44.451.5330–1.5670 (84–70 %)not listed—1.5551 in / 39.50 mm—
2-4½ UNC2.0000 / 50.801.7590–1.7950 (83–71 %)not listed—1.7812 in / 45.24 mm—
2-1/4-4½ UNC2.2500 / 57.152.0090–2.0450 (83–71 %)not listed—2.0312 in / 51.59 mm—
2-1/2-4 UNC2.5000 / 63.502.2290–2.2670 (83–72 %)not listed—2.2500 in / 57.15 mm—
2-3/4-4 UNC2.7500 / 69.852.4790–2.5170 (83–72 %)not listed—2.5000 in / 63.50 mm—
3-4 UNC3.0000 / 76.202.7290–2.7670 (83–72 %)not listed—2.7500 in / 69.85 mm—

How to read the tap drill chart

  • Tap drill, cutting tap is Greenfield's recommendation for cut (fluted) taps. Number drills are shown as #, letter drills as a capital letter, and the rest are fractional inch or metric drills. Thread % is calculated from the drill's nominal diameter with the formula above.
  • Minor Ø, class 2B is the smallest and largest minor diameter ASME B1.1 allows for the internal (nut) thread, as printed in Emuge's chart. The percentages in brackets are the thread depth at those two limits. Any drill that leaves the finished hole inside this band gives a thread that meets class 2B.
  • Hole Ø, Emuge is Emuge's recommended hole diameter. Emuge usually aims higher in the band than Greenfield, for example 0.204 in (#6 drill, 71 %) against #7 (0.201 in, 75 %) for 1/4-20. Emuge says its sizes are "reference values" that may have to be changed to suit the job.
  • Drill for a forming tap: thread-forming (roll) taps push the metal into the thread instead of cutting it, so they need a much larger hole. 1/4-20 takes a #1 drill (0.228 in) instead of #7. Greenfield lists no forming taps above 3/4 in.
  • The makers disagree on a few sizes. For 10-24, Greenfield gives #26 (79 %) where Regal and most charts give #25 (75 %). For 3-56, Greenfield gives #46 (78 %) and Regal gives #46 or #45 (73 %). For 12-28, Greenfield gives #15 (78 %), and Regal gives #16, #15 or #14 (84, 78 and 73 %). All of these fall inside the class 2B limits.
  • Above 1-1/2 in Greenfield lists no drills. The UNC rows from 1-3/4 in up show Emuge's holes, which are usually bored or interpolated rather than drilled at that size.

UNEF (extra-fine) tap drills

ThreadMajor Ø (in / mm)Minor Ø min–max (in)Thread % at the limits (calc.)Hole Ø, Emuge (in / mm)Thread % at Emuge hole (calc.)
#12-32 UNEF0.2160 / 5.490.1820–0.1900 (2B)84–64 %0.1875 / 4.7670 %
1/4-32 UNEF0.2500 / 6.350.2160–0.2240 (2B)84–64 %0.2205 / 5.6073 %
5/16-32 UNEF0.3125 / 7.940.2790–0.2860 (2B)83–65 %0.2835 / 7.2071 %
3/8-32 UNEF0.3750 / 9.530.3410–0.3490 (2B)84–64 %0.3465 / 8.8070 %
7/16-28 UNEF0.4375 / 11.110.3990–0.4070 (2B)83–66 %0.4040 / 10.2672 %
1/2-28 UNEF0.5000 / 12.700.4610–0.4700 (2B)84–65 %0.4646 / 11.8076 %
9/16-24 UNEF0.5625 / 14.290.5170–0.5270 (2B)84–66 %0.5236 / 13.3072 %
5/8-24 UNEF0.6250 / 15.880.5800–0.5900 (2B)83–65 %0.5807 / 14.7582 %
11/16-24 UNEF0.6875 / 17.460.6424–0.6494 (3B)83–70 %not listed—
3/4-20 UNEF0.7500 / 19.050.6960–0.7070 (2B)83–66 %0.6988 / 17.7579 %
13/16-20 UNEF0.8125 / 20.640.7584–0.7662 (3B)83–71 %not listed—
7/8-20 UNEF0.8750 / 22.230.8210–0.8320 (2B)83–66 %0.8268 / 21.0074 %
15/16-20 UNEF0.9375 / 23.810.8834–0.8912 (3B)83–71 %not listed—
1-20 UNEF1.0000 / 25.400.9460–0.9570 (2B)83–66 %0.9531 / 24.2172 %
1-1/8-18 UNEF1.1250 / 28.581.0650–1.0780 (2B)83–65 %1.0728 / 27.2572 %
1-1/4-18 UNEF1.2500 / 31.751.1900–1.2030 (2B)83–65 %1.2008 / 30.5068 %
1-3/8-18 UNEF1.3750 / 34.931.3150–1.3280 (2B)83–65 %1.3189 / 33.5078 %
1-1/2-18 UNEF1.5000 / 38.101.4400–1.4530 (2B)83–65 %1.4488 / 36.8071 %

Notes on UNEF

  • UNEF limits and holes are from Emuge (class 2B). 11/16-24, 13/16-20 and 15/16-20 are not in Emuge's chart. For those three, the minimum is the basic internal minor diameter (major − 1.0825 ÷ TPI) and the maximum is Greenfield's class 3B limit, and no maker drill is listed.
  • Earlier versions of this page gave 33/64 in for 9/16-24, 37/64 in for 5/8-24 and 41/64 in for 11/16-24. All three are smaller than the minimum minor diameter (0.517, 0.580 and 0.6424 in), so they would leave a hole too small for a class 2B or 3B thread.

Percentage of thread with stock drills (Regal)

TapDrillDrill Ø (in / mm)Theoretical thread (%)Probable hole Ø (in)Probable thread (%)
0-80#560.0465 / 1.1883 %0.048074 %
3/640.0469 / 1.1981 %0.048471 %
1-64#540.0550 / 1.4089 %0.056581 %
#530.0595 / 1.5167 %0.061059 %
1-72#530.0595 / 1.5175 %0.061067 %
1/160.0625 / 1.5958 %0.064050 %
2-56#510.0670 / 1.7082 %0.068774 %
#500.0700 / 1.7869 %0.071762 %
2-64#500.0700 / 1.7879 %0.071770 %
#490.0730 / 1.8564 %0.074756 %
3-48#480.0760 / 1.9385 %0.077978 %
5/640.0781 / 1.9877 %0.080070 %
#470.0785 / 1.9976 %0.080469 %
#460.0810 / 2.0667 %0.082960 %
#450.0820 / 2.0863 %0.083956 %
3-56#460.0810 / 2.0678 %0.082969 %
#450.0820 / 2.0873 %0.083965 %
4-40#440.0860 / 2.1880 %0.088074 %
#430.0890 / 2.2671 %0.091065 %
4-48#420.0935 / 2.3768 %0.095561 %
3/320.0938 / 2.3868 %0.095860 %
5-40#400.0980 / 2.4983 %0.100376 %
#390.0995 / 2.5379 %0.101871 %
#380.1015 / 2.5872 %0.103865 %
5-44#380.1015 / 2.5879 %0.103872 %
#370.1040 / 2.6471 %0.106363 %
6-32#370.1040 / 2.6484 %0.106378 %
#360.1065 / 2.7178 %0.108872 %
7/640.1094 / 2.7870 %0.112064 %
#350.1100 / 2.7969 %0.112663 %
#340.1110 / 2.8267 %0.113660 %
6-40#340.1110 / 2.8283 %0.113675 %
#330.1130 / 2.8777 %0.115669 %
#320.1160 / 2.9568 %0.118660 %
8-32#290.1360 / 3.4569 %0.138962 %
8-36#290.1360 / 3.4578 %0.138970 %
10-24#270.1440 / 3.6685 %0.147279 %
#260.1470 / 3.7379 %0.150274 %
#250.1495 / 3.8075 %0.152769 %
#240.1520 / 3.8670 %0.155264 %
10-325/320.1563 / 3.9783 %0.159575 %
#220.1570 / 3.9981 %0.160273 %
#210.1590 / 4.0476 %0.162268 %
12-2411/640.1719 / 4.3782 %0.175475 %
#170.1730 / 4.3979 %0.176573 %
#160.1770 / 4.5072 %0.180566 %
12-28#160.1770 / 4.5084 %0.180577 %
#150.1800 / 4.5778 %0.183570 %
#140.1820 / 4.6273 %0.185566 %
1/4-20#90.1960 / 4.9883 %0.199877 %
#80.1990 / 5.0579 %0.202873 %
#70.2010 / 5.1175 %0.204870 %
13/640.2031 / 5.1672 %0.206966 %
1/4-28#30.2130 / 5.4180 %0.216872 %
5/16-18F0.2570 / 6.5377 %0.260872 %
G0.2610 / 6.6371 %0.265166 %
5/16-24H0.2660 / 6.7686 %0.270178 %
I0.2720 / 6.9175 %0.276167 %
3/8-165/160.3125 / 7.9477 %0.316972 %
O0.3160 / 8.0373 %0.320468 %
3/8-2421/640.3281 / 8.3387 %0.332579 %
Q0.3320 / 8.4379 %0.336471 %
7/16-14T0.3580 / 9.0986 %0.362681 %
23/640.3594 / 9.1384 %0.364079 %
U0.3680 / 9.3575 %0.372670 %
7/16-20W0.3860 / 9.8079 %0.390672 %
25/640.3906 / 9.9272 %0.395265 %
1/2-1327/640.4219 / 10.7278 %0.426673 %
1/2-2029/640.4531 / 11.5172 %0.457865 %
9/16-1215/320.4688 / 11.9187 %0.473682 %
31/640.4844 / 12.3072 %0.489268 %
9/16-181/20.5000 / 12.7087 %0.504880 %
5/8-1117/320.5313 / 13.5079 %0.536275 %
5/8-189/160.5625 / 14.2987 %0.567480 %
3/4-1041/640.6406 / 16.2784 %0.645680 %
21/320.6563 / 16.6772 %0.661368 %
3/4-1611/160.6875 / 17.4677 %0.692571 %
7/8-949/640.7656 / 19.4576 %0.770872 %
7/8-1451/640.7969 / 20.2484 %0.802179 %
1-855/640.8594 / 21.8387 %0.865383 %
7/80.8750 / 22.2377 %0.880973 %
1-1229/320.9063 / 23.0287 %0.912281 %
59/640.9219 / 23.4272 %0.927967 %
1-1459/640.9219 / 23.4284 %0.927978 %
1-1/8-731/320.9688 / 24.6184 %0.975081 %
63/640.9844 / 25.0076 %0.991172 %
1-1/641.0156 / 25.8059 %1.022655 %
1-1/8-121-1/321.0313 / 26.2087 %1.038480 %
1-1/4-71-3/321.0938 / 27.7884 %reaming recommended—
1-7/641.1094 / 28.1876 %reaming recommended—
1-1/4-121-11/641.1719 / 29.7772 %reaming recommended—
1-3/8-121-19/641.2969 / 32.9472 %reaming recommended—
1-1/2-61-21/641.3281 / 33.7379 %reaming recommended—
1-11/321.3438 / 34.1372 %reaming recommended—
1-1/2-121-27/641.4219 / 36.1272 %reaming recommended—
1-3/8-61-13/641.2031 / 30.5679 %reaming recommended—
1-7/321.2188 / 30.9672 %reaming recommended—

Why the hole comes out bigger than the drill

  • Regal lists two figures for each drill. Theoretical % uses the drill's nominal size. Probable % adds the mean amount a twist drill cuts oversize (0.0015 in for the smallest drills, 0.0038 in around 1/4 in, about 0.006 in at 1 in and 0.007 in at 1-1/8 in). A #7 drill in a 1/4-20 hole, for example, is 75 % in theory and about 70 % in practice.
  • Every theoretical percentage in Regal's table matches TPI × (major − drill) ÷ 0.01299 to within one point. Three printed values are misprints, corrected here: #27 is 0.1440 in (printed .1140), 5/32 in is 0.1563 in (printed .1653), and the probable hole for #24 is 0.1552 in (printed .1152).
  • Regal lists no probable hole above 1-1/8 in and recommends reaming there. 1-14 is a UNS size that Regal includes but Greenfield and Emuge do not.

Percent-of-thread formulas

Percent of thread (inch)% = TPI × (major Ø − drill Ø) ÷ 0.01299. Example: 1/4-20 with a #7 drill: 20 × (0.250 − 0.201) ÷ 0.01299 = 75 %.
Drill for a chosen %drill Ø = major Ø − (0.01299 × %) ÷ TPI. Example: 1/4-20 at 65 %: 0.250 − 0.01299 × 65 ÷ 20 = 0.2078 in. That is just over the 2B maximum of 0.2070 in, so 65 % is too shallow for that thread.
Where 0.01299 comes fromRegal prints the metric version, % = 76.98 × (D − drill) ÷ P. Since 100 ÷ 76.98 = 1.299 and P = 1 ÷ TPI, the inch form is % = TPI × (D − drill) ÷ 0.01299. 100 % therefore means a hole 1.299 × P smaller than the major diameter, which is twice 0.6495 P, the height of the basic thread form.
Class 2B minimum minor Ømajor Ø − 1.0825 × P (the basic minor diameter of the nut thread). Emuge's minimum values match this to within 0.0012 in for every UN size listed.

Clearance drill sizes for inch screws (close and normal fit)

Screw sizeMajor Ø (in)Close-fit clearance drill (in / mm)Normal-fit clearance drill (in / mm)
#00.060#51 = 0.0670 in / 1.70 mm#49 = 0.0730 in / 1.85 mm
#10.073#46 = 0.0810 in / 2.06 mm#43 = 0.0890 in / 2.26 mm
#20.0863/32 in = 0.0937 in / 2.38 mm#36 = 0.1065 in / 2.71 mm
#30.099#36 = 0.1065 in / 2.71 mm#31 = 0.1200 in / 3.05 mm
#40.1121/8 in = 0.1250 in / 3.18 mm#29 = 0.1360 in / 3.45 mm
#50.1259/64 in = 0.1406 in / 3.57 mm#23 = 0.1540 in / 3.91 mm
#60.138#23 = 0.1540 in / 3.91 mm#18 = 0.1695 in / 4.31 mm
#80.164#15 = 0.1800 in / 4.57 mm#10 = 0.1935 in / 4.91 mm
#100.190#5 = 0.2055 in / 5.22 mm#2 = 0.2210 in / 5.61 mm
1/40.25017/64 in = 0.2656 in / 6.75 mm9/32 in = 0.2812 in / 7.14 mm
5/160.31321/64 in = 0.3281 in / 8.33 mm11/32 in = 0.3437 in / 8.73 mm
3/80.37525/64 in = 0.3906 in / 9.92 mm13/32 in = 0.4062 in / 10.32 mm
7/160.43829/64 in = 0.4531 in / 11.51 mm15/32 in = 0.4687 in / 11.90 mm
1/20.50033/64 in = 0.5156 in / 13.10 mm17/32 in = 0.5312 in / 13.49 mm
5/80.62541/64 in = 0.6406 in / 16.27 mm21/32 in = 0.6562 in / 16.67 mm
3/40.75049/64 in = 0.7656 in / 19.45 mm25/32 in = 0.7812 in / 19.84 mm
7/80.87557/64 in = 0.8906 in / 22.62 mm29/32 in = 0.9062 in / 23.02 mm
11.0001-1/64 in = 1.0156 in / 25.80 mm1-1/32 in = 1.0312 in / 26.19 mm
1-1/41.2501-9/32 in = 1.2812 in / 32.54 mm1-5/16 in = 1.3125 in / 33.34 mm
1-1/21.5001-17/32 in = 1.5312 in / 38.89 mm1-9/16 in = 1.5625 in / 39.69 mm

Close fit or normal fit?

  • Clearance drills are Unbrako's "Drill and Counterbore Sizes for Inch Socket Head Cap Screws". Close fit is meant for screws threaded to the head in assemblies with only one screw, or where the holes are made at assembly or with matched tooling. Normal fit is for longer screws, or for two or more screws in holes made by ordinary tolerancing.
  • Unbrako also recommends breaking the edge of the hole when the part is about as hard as the screw, so the underhead fillet is not damaged. For counterbore and countersink sizes see the countersink and counterbore chart.
  • Earlier versions of this page used a different, unsourced set of "close" and "free" fit drills, some tighter than Unbrako's (for example #9, 0.196 in, as a close fit for a 0.190 in #10 screw, where Unbrako gives #5, 0.2055 in). Those have been replaced.

Tapping fluids by material (US Army TC 9-524)

MaterialFluids listed for tapping
AluminumSoluble oil, mineral oil
BrassSoluble oil, lard oil, dry
BronzeSoluble oil, lard oil, dry
Cast ironMineral lard oil
CopperSoluble oil, mineral lard oil
Malleable ironSoluble oil
MonelMineral lard oil, sulfurized oil
Steel alloysSulfurized oil, mineral oil
Low-carbon steel forgingsSoluble oil, lard oil
Tool steelMineral lard oil, sulfurized oil

Sources

  • Greenfield Industries, Threading Catalog, 2024 (documents.mrosupply.com/file_uploads/2024GreenfieldThreadingCatalog.pdf). Used for: p. 5 "Tap Drill Recommendations" for cutting and forming taps; pp. 53–55 "Basic Thread Dimensions" (basic major, pitch and minor diameters, class 3B maximum minor diameter).
  • EMUGE Corp., Tap Drill and Thread Chart (wall chart ZS10021 US, Rev. B), 2011 (emuge.com). Used for: internal-thread minor-diameter limits (UN class 2B per ASME B1.1 Table 2; ISO metric 6H per ISO 965-1) and recommended tap drill sizes for UNC, UNF, UNEF, M and MF threads.
  • Regal Cutting Tools, Product catalogue, Engineering Data: "Tap Drill Sizes" and "Tap Drill Sizes for Metrics", current catalogue (regalcuttingtools.com). Used for: theoretical and probable percentage of thread for stock drill sizes (catalogue pp. 197–200), and the metric percentage-of-thread formula (76.980 ÷ pitch).
  • Unbrako, Socket Products Engineering Guide, current edition (unbrako.com/images/downloads/engguide.pdf). Used for: "Drill and Counterbore Sizes" for inch and metric socket head cap screws: close-fit and normal-fit clearance drills (pp. 82–83).
  • Headquarters, Department of the Army, TC 9-524 Fundamentals of Machine Tools (1996), Table 4-3 "Recommended Cutting Fluids for Various Materials" (armypubs.army.mil/epubs/DR_pubs/DR_a/pdf/web/tc9_524.pdf).
  • Standard referred to: ASME B1.1, Unified Inch Screw Threads (UN and UNR Thread Form). It is paywalled, so the class 2B limits come from Emuge's reproduction of its Table 2. Percent-of-thread figures marked "calc." are worked out on this page with the formula above, not copied from a maker.

Frequently asked questions

What size drill do I use for a 1/4-20 tap?

A #7 drill (0.201 in, 5.11 mm). Greenfield and Regal both list it, and it cuts about 75 % of full thread. Regal also gives #8 (0.199 in, 79 %) and 13/64 in (0.2031 in, 72 %). For a thread-forming tap use a #1 drill (0.228 in) instead (Greenfield).

What is the tap drill for 10-24 and 10-32?

10-24 UNC: Greenfield lists a #26 drill (0.147 in, 79 % thread), and Regal also lists #25 (0.1495 in, 75 %). 10-32 UNF: a #21 drill (0.159 in, 76 %). Emuge's holes are a little larger: 0.152 in for 10-24 and 0.1614 in for 10-32.

What does 75 % thread mean, and why not 100 %?

It is how deep the thread is cut compared with the full basic thread depth. Percent of thread = TPI × (major diameter − drill) ÷ 0.01299. ASME B1.1 class 2B allows a 1/4-20 nut thread minor diameter of 0.1960–0.2070 in (Emuge), about 83 % down to 66 % thread, so a 100 % hole is out of tolerance. Smaller holes also make the tap work much harder.

What drill for 5/16-18, 3/8-16 and 1/2-13 taps?

5/16-18 takes an F drill (0.257 in, 77 % thread), 3/8-16 takes 5/16 in (0.3125 in, 77 %) and 1/2-13 takes 27/64 in (0.4219 in, 78 %), according to Greenfield and Regal. The fine threads 5/16-24, 3/8-24 and 1/2-20 take I, Q and 29/64 in.

What size clearance hole for a 1/4 in bolt?

For a 1/4 in socket head cap screw Unbrako gives a 17/64 in drill (0.2656 in) for a close fit and 9/32 in (0.2812 in) for a normal fit. A #10 screw takes #5 (0.2055 in) or #2 (0.221 in), and 3/8 in takes 25/64 in or 13/32 in.

Was this article helpful?