Electronics

Resistor Tolerance Table

E-series preferred values (E6, E12, E24, E48, E96) and tolerance bands.

Tolerance → E-series

±20%E6: 1.0, 1.5, 2.2, 3.3, 4.7, 6.8 (rarely stocked today)
±10%E12
±5%E24
±2%E48
±1%E96 (most common 1% series)
±0.5% or betterE192

E24 (±5%) values

Values (× 10ⁿ Ω)
First decade1.0, 1.1, 1.2, 1.3, 1.5, 1.6, 1.8, 2.0, 2.2, 2.4, 2.7, 3.0
Second half3.3, 3.6, 3.9, 4.3, 4.7, 5.1, 5.6, 6.2, 6.8, 7.5, 8.2, 9.1

E12 (±10%) values

Values1.0, 1.2, 1.5, 1.8, 2.2, 2.7, 3.3, 3.9, 4.7, 5.6, 6.8, 8.2

Power ratings (common)

PackagePower
04021/16 W
06031/10 W
08051/8 W
12061/4 W
12101/3 W
20103/4 W
25121 W

Worked example: tolerance in a voltage divider

Two nominal 10 kilohm resistors divide a 5 V supply, so the ideal output is 2.5 V. With 1% parts, the worst case occurs when one is 1% high and the other 1% low: Vout = 5 × 9,900 / (10,100 + 9,900) = 5 × 0.495 = 2.475 V, which is 1.0% below nominal. The output therefore lies between 2.475 V and 2.525 V. With 5% parts, the worst case is 5 × 9,500 / (10,500 + 9,500) = 2.375 V, a 5% error. The error in a divider ratio is roughly equal to the tolerance of one resistor, so tolerance directly sets the accuracy of any ADC reference divider or feedback network.

Why the series has the numbers it does: the E-series divide each decade into equal ratio steps: E12 has 12 per decade (each step is 101/12 = 1.21, or 21% apart), E24 has 24 (step 10%), E96 has 96 (step 2.4%). Each value sits within one tolerance of its neighbor so the series covers every resistance without a gap.

Practical points

  • Tolerance is only part of the error. Temperature coefficient adds to it: a 100 ppm/°C thick-film resistor that warms by 50 °C shifts by 100 × 50 = 5,000 ppm = 0.5%.
  • For ratios, matching beats absolute tolerance. A matched network or an array in one package tracks within 0.05% or better, even when the absolute tolerance is looser.
  • Hit odd values with two resistors. To get 5.0 kilohms, put two 10 kilohm resistors in parallel. To get 4.5 kilohms, use 3.3 kilohms in series with 1.2 kilohms. The combined tolerance is no worse than the worst part.
  • 1% parts cost little more than 5% today, so for new designs 1% (E96) is the usual default for anything beyond an LED current limit.

Notes

  • Derate resistor dissipation to ~50% of rating for reliability and thermal margin.
  • Thin-film (0.1%) and wirewound resistors have much better tempco than thick-film (typically ±100 ppm/°C).
Was this article helpful?