Paver Calculator
Work out how many pavers a patio, path or driveway needs, plus the compacted gravel base, bedding sand and edge restraint, for any paver size and pattern.
How to Use
- Pick the shape of the area, or enter its square footage.
- Enter the paver size and the gap between pavers; most concrete pavers are laid almost tight, about 1/16 to ⅛ in.
- Choose the pattern: running bond and basket weave need about 5% extra, herringbone at 45° about 15%.
- Set the base depth: about 4–6 in for a patio or path, 8–12 in for a driveway.
- Read the pavers, the base and sand in tons, and the length of edging.
Worked Example
A patio 16 × 12 ft in 4 × 8 in pavers, running bond, on a 4 in base. Area = 192 ft². One paver covers 4 × 8 = 32 in², so a square foot takes 144 ÷ 32 = 4.5 pavers: 192 × 4.5 = 864 pavers, and with 5% waste 908.
Base: 192 ft² × 4 in = 64 ft³ finished; crusher run loses about 20% when compacted, so order 76.8 ft³ = 2.84 yd³, about 4.3 tons at 1.5 t/yd³. Sand: 192 × 1 in = 16 ft³ = 0.59 yd³, about 0.8 tons. Edging: the perimeter, 2 × (16 + 12) = 56 ft, less any side against the house.
The common mistake: a thick sand bed instead of a deep base. Making up height with 3 in of sand over a thin base lets pavers sink and rut within a season. The sand should stay at about 1 in; the gravel base below does the work.
Show Work
Formulas
How a Paver Patio Is Built
Interlocking concrete pavers are a flexible pavement: each unit can move slightly, and the load spreads through the sand-filled joints and the compacted base. The layers, from the bottom: compacted subgrade, often a geotextile fabric, a crushed-stone base compacted in lifts, a 1 in screeded sand bed, the pavers, then joint sand swept in and the whole surface compacted again so the pavers settle into the sand.
Build in a slope of about ¼ in per foot (2%) away from buildings so water runs off. Modern interlocking concrete pavers were developed in the Netherlands and Germany after the Second World War, to rebuild streets quickly; their roots go back to the stone-paved roads of Rome.
About This Calculator
This calculator counts pavers for a rectangle, a circle or any area from the paver size and joint, adds waste for the pattern, and works out the compacted gravel base, the bedding sand and the edging. It draws the area with the pavers laid in running bond, in feet and inches or metres and millimetres.
Everything runs in your browser; nothing is sent anywhere. Material weights are typical; use your supplier’s figures when you have them.
Related calculators: Gravel Calculator, Concrete Calculator, and Retaining Wall Calculator.
Frequently Asked Questions
How many pavers do I need?
Divide the area by the area of one paver including its joint, then add waste for cuts. A 4×8 in paver covers 32 in², so 4.5 per square foot; a 16×12 ft patio of 192 ft² takes 864 pavers, 908 with 5% waste.
How deep should the paver base be?
For a patio or walkway, about 4 to 6 in of compacted crushed gravel base; for a driveway, 8 to 12 in, more on clay soil or in freezing climates. Compact it in 2 to 3 in lifts with a plate compactor. The base, not the pavers, carries the load.
How much sand goes under pavers?
A 1 in (25 mm) screeded layer of coarse concrete sand, never more than about 1½ in, because thick sand lets pavers rut and shift. 192 ft² at 1 in is 16 ft³, about 0.59 yd³ or 0.8 tons. Joints are filled afterwards with fine or polymeric sand.
Do pavers need edge restraint?
Yes. Without a firm edge, pavers creep outward and the joints open. Plastic or aluminium edging spiked into the base, a concrete haunch, or a soldier course set in concrete all work. You need edging along every edge not held by a wall or a step.
Why add more waste for herringbone?
At 45°, every paver along the edge is cut at an angle, and the offcuts are rarely reusable. Straight running bond along the edges wastes far less. Herringbone is worth it on driveways, though, because the interlock resists the twisting of car tyres.
How do I use the Paver Calculator?
Simply type your numbers and read the result, which refreshes the instant you change something. There is nothing to submit and nothing to wait for.
Do I need to install or sign up for anything?
Not at all — it runs in the browser with nothing to install and no account. After it loads once, it even works without an internet connection.
Is my information private?
Yes. Everything happens in your browser. Nothing you type is sent to a server or saved anywhere.
Common Use Cases
Patio
16×12 ft in 4×8 in pavers: 864 before waste, 908 with 5%; 4 in base is 2.84 yd³ with compaction.
Driveway
40×12 ft in 4×8 in pavers at 45° herringbone with 15% waste: 2,484 pavers, on a 10 in base.
Round patio
A 12 ft circle in 6×9 in pavers: 113 ft², 302 pavers before waste.
Path
30 ft × 3 ft in 12×12 in slabs: 90 slabs before waste and 66 ft of edging.
Metric patio
5×4 m in 200×100 mm blocks: 1,000 blocks before waste.
Last updated: